Nov 10 2011
Replacing Intake Manifold Gaskets on 3.1 L GM Engines and others
Removing an intake manifold from a V-6 or V-8 can be quite a complex task or it can be simple. Of course, if you are replacing a standard intake manifold with a high-performance one, you might take a few short cuts – unless you want to be sure that the manifold and all components can be used again.
But if you are rectifying a problem on an ordinary auto it is different; you might be ,replacing intake manifold gaskets on 3.1 l gm engines, or want to know how to remove intake manifold on chevy tahoe, but the principles are the same. It is basically a question of removing the intake manifold, cleaning it up, and putting it back – but taking care with some parts of the job. Also you need to be careful when replacing a intake manifold gasket.
Let’s look at how to remove intake manifold on chevy tahoe. This is not so complicated, except thjat yuo have to remove the wiring harness which is in the way, and a few other things first. You also have to remove the distributor, and want to make sure you get that back in the right position.
Make sure that you get the right gaskets before you start, so you don’t have to waste time later. Whatever the model, you need to follow instructions or 2001 nissan alitma intake manifold removal steps with this particular auto. Or, you might wonder how to replace intake manifold on 1991 isuzu trooper or another import. Don’t worry, just be methodical and it will work out OK.
If you are an enthusiast, you might also want to improve air-flow by either enlarging the ports and passages in the manifold, or just by making sure they align correctly. Of course, if it is one of these modern plastic intake manifolds there is not much you can do to it as the walls are thin, and precision moulded anyway. If it is not getting enough air through you need an aftermarket manifold. It is still worth checking alignment, though, as you can alter the ports in the head to suit.
With an old carburetor manifold, the first job is to remove the air filter and carburetor, and make sure that the fuel pipe is covered and cannot leak fuel all over the floor of the workshop. If you have fuel injection, then there is no carburetor, but the intake manifold is usually more complex, especially on a V-8, where the manifold is between the two banks. There are quite a few things to be removed before you can get at the manifold itself, such as engine covers, the air filter, or air filter pipe.
Remove all wiring, see if there are water passages in the manifold
In addition there are usually some electrical components that are in the way, and the air sensing meter which needs to be either disconnected or removed. The other important point is to find out whether the intake manifold also contains water passages, which is quite common, especially on V-8s. In that case, you need to make sure that the water is drained from the engine before you start work on removing the manifold. If in doubt, drain the cooling system! Every so often, you need to check that you are following instructions, such as 2001 nissan alitma intake manifold removal steps.
Once all the auxiliaries are removed, the job of removing the manifold itself is fairly straightforward – but is complicated on some cars such as the BMW V-8s because of all the other components affected – so long as you can reach the bolts holding the manifold in place with a spanner or socket. You need to be careful when you remove it, and make sure you get the gasket off at the same time. You will need to fit a new gasket, so if you are replacing intake manifold gaskets on 3.1 l gm engines, don’t worry about damaging it.
You will also need to clean up the faces, removing any bits of gasket and carbon. At this point you can check how well the manifold and ports line up. You need to get some marking paste and put it over the joint faces of the cylinder heads, and place the manifold back on the engine. The paste will transfer to the faces of the manifold, so you can see whether they align. The next job is to decide whether you want to just modify the manifold to suit, or you want to enlarge the ports and manifold.
When it comes to replacing a intake manifold gasket, you need to make sure that the joint faces are both clean, and if not lightly sand them down. Use a good jointing compound, and then reassemble the engine. Make sure you put the gasket in correctly, too.
Mail this post